Science & technology
Biomechanics: gait, the spine and the three-point force principle in orthoses
Biomechanics is “the physics of the living body”. This article explains three core topics in plain language: the gait cycle and the forces on the leg, disc pressure when bending and lifting and the vicious cycle of scoliosis, and the three-point force principle that lets an orthosis correct the spine – with measured data from reputable studies and 8 illustrations.
Biomechanics is the science that applies the laws of mechanics – force, motion, levers, moments – to the living body: how each part moves, how much load it carries, why it gets injured and how to intervene correctly (exercise, orthoses, surgery).
This article covers three foundations of orthotics: (1) the biomechanics of gait, (2) the biomechanics of the spine, (3) the three-point force principle in orthoses. Each part starts from the physical mechanism and then gives measured data from verified scientific studies (reference list at the end).
Part 1. Biomechanics of gait
The gait cycle starts when one heel strikes the ground and ends when the same heel strikes the ground again. It is measured in percent (0–100%) rather than seconds, so fast and slow walkers can be compared.
At normal walking speed about 60% of the cycle is stance (about 40% single-limb and 20% double-limb support) and 40% is swing (AAPM&R). The two periods with both feet on the ground take 20–24% of the cycle – the basic difference between walking and running: in running there are moments when both feet are in the air.
| Phase (Rancho Los Amigos / Perry) | % of cycle | What happens |
|---|---|---|
| Initial contact | 0% | Heel strikes the ground, weight acceptance begins |
| Loading response | 0–10% | Body weight shifts onto the leg, the knee flexes slightly to absorb shock |
| Midstance | 10–30% | The body passes over the foot; one leg carries the full body weight |
| Terminal stance | 30–50% | The heel rises; the body rolls over the forefoot |
| Preswing | 50–60% | The other foot is already down; this leg prepares to lift |
| Initial swing | 60–73% | Toes leave the ground; hip and knee flex to lift the leg |
| Midswing | 73–87% | The leg moves forward; the shank is vertical |
| Terminal swing | 87–100% | The knee extends, ready for the next heel strike |
Initial swing lasts from toe-off until maximum knee flexion of about 60° – the knee must bend enough for the foot to clear the ground. That is why people with a stiff knee or lack of ankle dorsiflexion range must compensate, for example by swinging the leg outward or rising on the other foot.
Forces in gait: ground reaction and internal forces
By Newton's third law, the ground pushes back on the foot as hard as the foot pushes on the ground – the ground reaction force, measured with a force plate. When walking, the ground does not only support body weight but must also brake the falling body and push it up and forward, so the force exceeds body weight. Nilsson and Thorstensson (Acta Physiol Scand 1989) measured peak vertical forces of 1.0–1.5 times body weight in walking and 2.0–2.9 times in running: for a 60 kg person each step loads the leg with the equivalent of 60–90 kg when walking and 120–175 kg when running.
The forces carried by bones and joints are several times larger, because muscles attach close to the joints (short lever arms) and must contract very strongly. Matijevich et al. (PLoS ONE 2019) summarise: in running the ground reaction force is usually 2–3 times body weight, but the force at the distal tibia reaches 6–14 times; even in walking a ground reaction force of 1.1 times body weight goes with a tibial compressive force of 4.1 times.
Meaning for orthotics: an insole or ankle orthosis can reduce only a small part of the external force, but if it changes the direction of the force and the lever arm around a joint it can greatly change the internal load on muscles and joints.
Part 2. Biomechanics of the spine
The spine is like a load-bearing column of stacked blocks: vertebral bodies are the compression blocks; the disc between them is a hydraulic shock absorber with the nucleus pulposus (a water-rich gel) in the centre and the annulus fibrosus – many crossed fibre layers like a tyre – around it; the facet joints act as guide rails; ligaments and paraspinal muscles are the cables that keep the column from falling.
The review by Izzo et al. (European Journal of Radiology 2013) describes spinal stability as the combined work of three subsystems: the passive subsystem (bones, discs, ligaments), the active subsystem (muscles and tendons) and the central nervous system that controls the other two. When one subsystem weakens – a degenerated disc or weak back muscles – the others must carry more.
The nucleus is almost incompressible, like water. Under load it pushes evenly in all directions against the annulus, which tightens to contain it – so compression is spread rather than concentrated. In forward bending the front of the disc is compressed, the back is stretched and the nucleus is pushed backward – towards the posterior annulus and posterior longitudinal ligament, the weakest point and the usual site of herniation.
Direct measurements of disc pressure
Wilke et al. (Spine 1999) implanted a 1.5 mm pressure sensor into the nucleus of a non-degenerated L4-L5 disc of a 45-year-old, 70 kg male volunteer and recorded pressure continuously for about 24 hours. It is one of the most cited studies in the field (Hou et al., Journal of Pain Research 2023).
| Position / activity | L4-L5 disc pressure | Compared with standing |
|---|---|---|
| Lying prone | 0.1 MPa | about 20% |
| Lying on the side | 0.12 MPa | about 24% |
| Standing relaxed | 0.5 MPa | 100% (reference) |
| Sitting without back support | 0.46 MPa | about 92% |
| Sitting, maximally flexed | 0.83 MPa | about 166% |
| Standing, bent forward | 1.1 MPa | about 220% |
| Lifting 20 kg close to the body | 1.1 MPa | about 220% |
| Lifting 20 kg with knees bent | 1.7 MPa | about 340% |
| Lifting 20 kg with a flexed back | 2.3 MPa | about 460% |
How to read the table: bending forward alone doubles the pressure; lifting the same 20 kg with a flexed back gives more than twice the pressure of holding it close to the body – a direct example of moment = force × distance: the farther the load from the spine, the harder the back muscles must pull and the more the disc is compressed.
Scientific note: Wilke did not confirm Nachemson's earlier conclusion that sitting loads the disc more than standing, and the study had only one participant. Rohlmann et al. (Ergonomics 2001) showed that when load shifts to the anterior column (trunk flexion, lifting) the trends of nucleus pressure and of bending moments measured on spinal fixators differ – in flexion the load also includes bending that stretches the posterior structures. Finite element models of L4-L5 summarised by Hou et al. likewise show disc pressure highest in flexion at every degeneration grade, and flexion combined with side bending or rotation raises stress most in the posterolateral annulus – the region prone to herniation. Bending combined with twisting (bending to lift something and turning to the side) is therefore the most dangerous combination for the lumbar disc.
Scoliosis and the “vicious cycle”
The Hueter–Volkmann law: in the growth plate (where bones lengthen in children), compression slows growth and distraction speeds it up. Stokes (Eur Spine J 2007; Stud Health Technol Inform 2008) describes how a scoliotic spine is loaded more on the concave side; the asymmetric load causes asymmetric growth, wedged vertebrae and a vicious cycle that makes the curve progress, especially during puberty.
The key point: according to Stokes, if the load asymmetry can be reversed, the vicious cycle is reversed too. This is the biomechanical basis for aiming to reduce the curve in growing children, not merely to hold it: when the orthosis pushes the spine the other way, the former concave side is unloaded and grows faster, the former convex side is compressed and grows slower, and the vertebrae gradually lose their wedge shape. Stokes's quantitative simulation predicts that a substantial part of progression during growth is biomechanical – and once the growth plates close, there is no longer a “machine” to reshape the bone.
Part 3. The three-point force principle in orthoses
Take a bent plastic ruler: to straighten it you press your thumb on the most curved point (the convex side) and hold both ends on the opposite side with two fingers. In a spinal orthosis the corrective force is applied at the apical vertebra and the counter-forces at the upper and lower ends of the curve, through the pads and the shell.
Why exactly three points? In static equilibrium a body stays still when the sum of forces is zero (it is not pushed away) and the sum of moments is zero (it does not rotate). Pushing at one point only shifts the trunk; two opposite points make it rotate; three points is the minimum that balances the forces while creating a bending moment against the curve.
Worked example: the main pad pushes F = 40 N (about 4 kg), each counter-force is F/2 = 20 N and the distance between the counter-forces is L. The bending moment at the apex is M = (F/2) × (L/2) = F × L / 4: with L = 20 cm, M = 2 N·m; with L = 40 cm, M = 4 N·m. For the same push, doubling the distance doubles the corrective moment – so the orthosis must be long enough to span the whole curve; a short orthosis must press very hard, which is painful and harms the skin. Wynne (developer of the Boston brace system, 2008) describes that when the trunk is shifted to one side, extra leverage is needed to bring the upper spine to the midline, so the brace is extended up to a thoracolumbar design.
Pressure: why corrective pads must be wide enough
Skin and soft tissue are injured by pressure, i.e. force divided by area (P = F / A). With the same 40 N: on a 20 cm² pad the pressure is 20 kPa; on a 5 cm² pad it is 80 kPa – four times higher. A study of 5 scoliosis patients (Journal of Industrial Textiles 2021) measured pad pressures of 6.0 to 24.4 kPa, and the pressure distribution showed that a three-point force system had formed to reduce the curve.
Design rule: to increase corrective force without causing sores, increase the contact area and fit the shell closely to the body contour – do not press hard with a small pad. This is also why plaster casting with hand correction directly on the patient makes the shell fit the skin closely.
From two-dimensional three-point systems to three-dimensional correction
Scoliosis is a three-dimensional deformity: lateral curvature, vertebral rotation and a disturbed sagittal profile. Modern orthoses therefore combine several three-point systems: Chêneau-type braces correct with multiple three-point force systems acting in three dimensions with the aim of overcorrection (hypercorrection), together with elongation and derotation. Every pressure zone is paired with an expansion zone (a free space) on the opposite side so the trunk and rib cage have room to move – without that space the push only squeezes soft tissue and cannot move the spine.
- The three-point system creates a bending moment against the curve.
- This moment reverses the load asymmetry: the former concave side is unloaded, the former convex side is compressed.
- By the Hueter–Volkmann law the unloaded growth plate grows faster and the compressed one slower.
- The wedged vertebrae gradually even out – the vicious cycle runs backwards.
- Overcorrection (past the midline) makes the load reversal clear and long enough to change growth.
Biomechanics is the foundation of every orthotic device: only by understanding force, moment and pressure can we design a corrective orthosis that works and is still safe for the skin. If you or your child has scoliosis, back pain from a disc herniation or a gait problem, contact us for an examination and advice: +84 985 211 888 (phone / Zalo).
References
- American Academy of Physical Medicine and Rehabilitation (AAPM&R). Biomechanics of normal gait. PM&R KnowledgeNow.
- Perry J. Gait Analysis: Normal and Pathological Function. SLACK; 1992 – Rancho Los Amigos terminology (summary: University of Oklahoma Health Sciences Center).
- Nilsson J, Thorstensson A. Ground reaction forces at different speeds of human walking and running. Acta Physiol Scand. 1989;136(2):217–227. PMID: 2782094.
- Matijevich ES, Branscombe LM, Scott LR, Zelik KE. Ground reaction force metrics are not strongly correlated with tibial bone load when running across speeds and slopes. PLoS ONE. 2019;14(1):e0210000 (CC BY).
- Wilke HJ, Neef P, Caimi M, Hoogland T, Claes LE. New in vivo measurements of pressures in the intervertebral disc in daily life. Spine. 1999;24(8):755–762. PMID: 10222525.
- Rohlmann A, Claes LE, Bergmann G, Graichen F, Neef P, Wilke HJ. Comparison of intradiscal pressures and spinal fixator loads for different body positions and exercises. Ergonomics. 2001;44(8).
- Izzo R, Guarnieri G, Guglielmi G, Muto M. Biomechanics of the spine. Part I: spinal stability. Eur J Radiol. 2013;82(1):118–126.
- Hou Z, Wang W, Su S, Chen Y, Chen L, Lu Y, Zhou H. Bibliometric and visualization analysis of biomechanical research on lumbar intervertebral disc. J Pain Res. 2023;16:3441–3462.
- Stokes IAF. Analysis and simulation of progressive adolescent scoliosis by biomechanical growth modulation. Eur Spine J. 2007;16(10):1621–1628. PMID: 17653775.
- Stokes IAF. Mechanical modulation of spinal growth and progression of adolescent scoliosis. Stud Health Technol Inform. 2008 (PMC3086537).
- Wynne JH. The Boston Brace and TriaC systems. Disabil Rehabil Assist Technol. 2008.
- Negrini S, et al. Brace technology thematic series: the Sforzesco and Sibilla braces, and the SPoRT concept. Scoliosis. 2011;6:8 (CC BY).
- Could novel spinal braces with flexibility, robotic components, and individualized design generate sufficient biomechanical treatment efficacy in patients with scoliosis? Bioengineering. 2025;12(10):1083.
- Design and fabrication of anisotropic textile brace for exerting corrective forces on spinal curvature. Journal of Industrial Textiles. 2021.
- Corrective orthoses for scoliosis: a systematic review (Bioengineering 2021) – Encyclopedia MDPI entry.
- Biomechanics of brace action used for conservative treatment in spinal deformity. In: Human Musculoskeletal Biomechanics. IntechOpen.
Do you or a loved one need advice?
Book an in-person assessment in Hanoi or send your file for a remote consultation. We reply within 24 hours.